Top positive review
2 people found this helpful
Parking was factory set to 300 seconds on my drives and they are working well.
By B.E.N.T. on Reviewed in the United States on March 8, 2015
I purchased two of the 3TB drives and one of the 2TB drives. When I went into WDIDLE3 the setting for all three drives were set to 300 seconds (5 minutes). Since I was in there I simply disabled it. These drives are working flawlessly thus far as I have the two 3TB drives in a media center running Media Browser 3, PlayOn, and a few other apps. The 2TB drive is hooked up to a Dish Network Hopper as a secondary storage. I have not experienced any issues so far with these drive. I will update as time goes on with more info. *Update 3/27/15: Some drive information obtained from HD Guardian: Drive 01 Serial Number: WD-WCC4N7E***** Firmware: 82.00A82 User Capacity: 3,000,592,982,016 bytes Product Name Status Exp Date (MM/DD/YYYY) 3 TB WD Red Hard Drive In Limited Warranty 1/6/2018 Overall Health: Temperature: 34*C High: 36*C Low: 34*C Last Test: Completed without error. No bad sector detected. No ATA error detected. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 185 182 021 Pre-fail Always - 5733 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 42 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 673 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 5 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 1 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 40 194 Temperature_Celsius 0x0022 116 110 000 Old_age Always - 34 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 Working Time: 673 hours (28 days, 1 hours) Last Update Fri Mar 27 01:53:28 2015 CDT Drive 02 Serial Number: WD-WMC4N0F***** Firmware: 82.00A82 User Capacity: 3,000,592,982,016 bytes Product Name Status Exp Date (MM/DD/YYYY) 3 TB WD Red Hard Drive In Limited Warranty 12/11/2017 Overall Health: Temperature: 37*C High: 41*C Low: 35*C Last Test: N/A No bad sector detected. No ATA error detected. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 181 179 021 Pre-fail Always - 5950 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 50 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 672 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 1 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 48 194 Temperature_Celsius 0x0022 113 109 000 Old_age Always - 37 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 Working Time: 672 hours (28 days) Last Update Fri Mar 27 01:53:28 2015 CDT ------------------------------------------- Update 5/14/2015 Some drive information obtained from HD Guardian: Drive 01 Serial Number: WD-WCC4N7E***** Firmware: 82.00A82 User Capacity: 3,000,592,982,016 bytes Product Name Status Exp Date (MM/DD/YYYY) 3 TB WD Red Hard Drive In Limited Warranty 1/6/2018 Overall Health: Temperature: 37*C High: 37*C Low: 34*C Last Test: Completed without error. No bad sector detected. No ATA error detected. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 186 182 021 Pre-fail Always - 5700 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 193 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 98 98 000 Old_age Always - 1844 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 5 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 1 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 190 194 Temperature_Celsius 0x0022 113 108 000 Old_age Always - 37 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 Working Time: 1844 hours (2 months 16 days, 20 hours) Last Update Fri May 14 22:31:35 2015 CDT Drive 02 Serial Number: WD-WMC4N0F***** Firmware: 82.00A82 User Capacity: 3,000,592,982,016 bytes Product Name Status Exp Date (MM/DD/YYYY) 3 TB WD Red Hard Drive In Limited Warranty 12/11/2017 Overall Health: Temperature: 37*C High: 41*C Low: 35*C Last Test: N/A No bad sector detected. No ATA error detected. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 181 179 021 Pre-fail Always - 5908 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 242 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 98 98 000 Old_age Always - 1836 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 5 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 1 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 240 194 Temperature_Celsius 0x0022 110 106 000 Old_age Always - 40 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 Working Time: 1836 hours (2 months, 16 days, 12 hours) Last Update Fri May 14 22:31:35 2015 CDT
Top critical review
6 people found this helpful
4x 3TB drives failed in 24 hours
By Atlantic on Reviewed in the United States on June 3, 2013
May 2014 - I forgot to update this, so I'm doing it almost a year later. Down graded to one star. TLDR - Amazon was great, however, 4 drives (two sets of two) failed in 24 hours. Extensive conversations with WD second level support resulting in them saying "return the drives", so I bought 3TB green drives again for the external enclosures, and 3TB Toshiba/Hitachi drives for the NAS. Very unimpressed with WD RED drives - all marketing on what are really just average drives. This is to justify continued higher costs after the flood farce perpetrated on the public. Yes, the flood happened, however, the raping of the customers has continued (easily researched what they've done, and prices don't lie). Lets hope SSDs come down in price soon.... ****** Original review ****** I'm leaving a generous, but temporary, 2-star review. My two drives failed within 24 hours and I'm awaiting replacement drives so I'll update this review after I've tested them. First, I want to state that Amazon's shipping was flawless and I don't think it was a problem for these drives. I currently own at least 25 WD drives (as well as many by other vendors) and ordered 2x 3TB Red drives for use first in external enclosures, and later to be put in a Synology NAS. They never made it past the enclosure stage, and were dead in a day. All work, no play, for me at least. 1) Drives were placed in USB 3.0 external enclosures, initialized as GPT under Win7 (x64), and a NTFS "Quick format" was performed. I then ran a SMART "Quick Test" using WD's Data Lifeguard (DLG), which passed fine. Note: DLG quick test only checks the first and last million sectors, leaving most of the drive unchecked. The drives were each loaded with approx 1.5TB of data, and then shutdown properly using "Safely remove hardware" before disconnecting. Note: the 1-year-old enclosures support 3TB drives - verified with the mfg again this morning - and were previously housing WD and Hitachi 2TB drives without issue. 2) Attempted to start the drives the next day, but they weren't identified by Explorer, and when finally found in Disk Management (under Admin -> Computer Management) they were once again showed as "Not initialized". They were in effect, dead to me. 3) I attempted to mount the drives on another, almost new, high-end computer running Win8 Pro. The drives were not seen by Explorer, but could be found under Disk Management, however, they showed with 2TB labeled "MBR protected" and 7xxGB "unallocated". No data could be read. 4) Contacted WD support. After discussing all events and options, their recommendation was "send'em back to us or Amazon, they're dead". 5) I accepted that something had gone wrong, but again using DLG, I tried a low level process called "Write Zeros". The first drive simply failed with bad sectors after running for 5 hours. I tried to "continue" the process by clicking the pop-up error window 50-100x times before finally giving up. I couldn't format it, couldn't write zeros, nothing worked. After several more attempts, I finally got it to finish a windows format (ran for the last 12 hours), but I don't trust it. The second drive did allow me to Write Zeros, but I don't trust it either. They're both going back. Write Zeros may temporarily "fix" drives, but may also just mask the underlying problem(s). (And yes, I understand erasing vs. formatting, the data implications, etc.). WD has a problem, and because of that so do we. I recommend everyone format and test these drives before use. I know drives fail; I've had many drive failures in the last couple of years (3 Seagate, 5 Samsung F4s, etc.) but all before they were mounted in a NAS. Read the reviews, understand that it's a lottery, and though I had hoped for more, I didn't win the first time. You may get lucky.... or.... you may not. I'll update this review after receiving my new drives, and have tested them in brand new enclosures.
Sort by:
Filter by:
By -
Verified Amazon Purchase
Vine Customer Review of Free Product
Sorry, no reviews match your current selections.
Try clearing or changing some filters.Show all reviews
Show more reviews